Tipa

Carbon monoxide detector - Measuring equipment - Model Kidde 7DCO
A new hi-tech solution from the category of carbon monoxide measuring devices with the first second generation electrochemical sensor and a de-ionized water electrolyte that tests every second for a fatal carbon monoxide (CO) hazard with LCD display that shows the current concentration level in the monitored area . The indications are displayed between 0 and 999PPM *.

The first nanowax conformal CO detector to protect the device electronics even in very humid environments. The device is thus suitable for placement or installation, for example in bathrooms with karma, gas boiler, boiler rooms and the like. The device performs repeated measurements every second. Exceeding the maximum CO level is indicated optically (by a red LED) and by an acoustic alarm (loudly pulsing with a signal strength of 85 dB).

The carbon monoxide meter is equipped with a Test / Reset button that is able to verify the correct operation of the device and a Peak / Level to display the highest CO level measured since the device memory reset. The status of the sensor, batteries, and internal circuits is monitored by the system of automatic efficiency control devices. If a fault is detected, the LCD will display information corresponding to the fault detected and a safety signal will be triggered. Battery power allows the device to be positioned in the optimal position. Thanks to the special design of the device, it can be placed not only on a wall in a room, but also on flat surfaces such as a bedside table.

Carbon monoxide is a colorless, tasteless and odorless gas produced by poor combustion of fossil fuels such as coal, oil, natural gas, LPG, coal and wood. It can also be produced by poorly maintained or broken down fuel burning domestic appliances such as: boilers, gas appliances, karma, grills, clogged chimneys, ventilation systems or damaged flue gas ducts. Common symptoms of CO poisoning include headaches, nausea, fatigue or muscle pain - but these can easily be confused with the diagnosis of influenza. It is therefore important to protect your family and home with carbon monoxide detectors.

CARBON OXIDE poisoning can prevent the detector of CO

Advantages of the device:
Kidde Electrochemical Technology - second generation sensors with de-ionized water electrolyte that performs testing every second
NANOWAX layer protecting the electronics of the device against moisture
LCD display with a maximum range of 999 PPM
100% longer lifetime compared to older models
Twice smaller in size than older models
Loud alarm signaling strength 85dB
Function Test / Reset - verification of correct functioning of the device
Peak / Level function - the highest measured CO level in memory
Battery power
Installation on a wall or flat surface
End-of-life signaling
Low operating costs, small size and weight
Simple assembly and handling
Timeless and modern design
10 year warranty
The carbon monoxide measuring device has a certificate confirming compliance with the requirements of the Czech technical standard ČSN-EN 50291: 2010 for domestic carbon monoxide detectors. Compliance with this standard has been confirmed by the British Standard Institute (BSI) independent research laboratory.

* For concentrations in the range of 0 - 30 PPM, the designation is "0".

Technical specifications:
Sensor Technology: Kidde's electrochemical technology - a patent, is one of the most accurate in the world.
Power supply: DC, three 1.5 V AA alkaline batteries (included).
Mounting method: Wall mounting (screws included) or flat surface.
Exceeding permissible CO concentration: 85 dB acoustic alarm and visual (red LED) indication of detected concentration on LCD panel.
End of Life Announcement: The “End” information on the LCD panel, two beeps and two red LEDs blink within 30 seconds.
Low Battery Indication: A “Lb” message on the LCD panel accompanied by a beep and a red and green LED.
LCD panel display: Current CO concentration level between 0 and 999 PPM * "Lb" - low battery, "Err" - unit failure. "End" - end of life notification
Function Test / Reset: Button for checking, maintaining the device. After it is pressed, the control unit performs a device test.
Peak / Level function: Button to recall the highest measured CO concentration stored in the instrument's memory within the range of 11 - 999PPM. When the button is pressed, the highest CO level detected at the time of device reset is displayed.
Operating temperature: from +0 to +40°C
Operating humidity: up to 90% relative humidity (RH) non-condensing.
Storage conditions: temperature: from -10 to +60°C, humidity: 5 - 95% RH
Dimensions: 118 × 70 × 40mm
Weight with batteries: 0.160 kg
Approval: ČSN-EN50291: 2010 part 1 households and part 2 (ships and trailers)
Stamps: CE
Warranty: 10 years