Tipa

Does your vehicle hurt rust, salted roads, creeping hinges or tangled locks? You have just found an ideal product to protect your car, quad bike or motorcycle from corrosion even in extreme conditions. Spray NANOPROTECH Auto Moto Anticor can easily solve all these problems. Its special composition uses nanotechnology to achieve significantly better results than competing products.

How do NANOPROTECH sprays work?

Our sprays use less than microscopic particles that fill even the smallest cracks, pores and inequalities after application. The treated surface is perfectly aligned to create an impenetrable barrier that removes moisture and prevents corrosion. In addition, a thin layer of nanoparticles, together with a special solution, greatly reduces friction and acts as a perfect lubricant. Spray NANOPROTECH Auto Moto Anticor is designed to withstand even rapid fluctuations in temperature in the engine compartment. The bulk version of 300 ml with the official name GNP Antirust Professional additionally brings not only a double volume but also a professional applicator with a short and long application tube for more practical application.

How to Spray NANOPROTECH Auto Moto Anticor can help?

- Protects against corrosion

Fifteen minutes after the NANOPROTECH Auto Moto Anticor solution is applied, a nanoparticle film is formed on the treated metal surface. It displaces moisture and, thanks to nanotechnology, prevents corrosion for much longer than comparable competitive products.

- Resistant to salty environment

The most demanding for cars is undoubtedly the winter season associated with salt on the roads. It can cause serious corrosion problems even in new cars over the course of several seasons. However, if the endangered parts, especially on the chassis of the car are treated before the winter season by NANOPROTECH Auto Moto Anticor spraying, they will be preserved and the salt will no longer harm them.

- Removes rust

If you have an older car or a motorcycle that is already starting to rust, the Auto Moto Anticor spray provides the ideal help. Apply the solution to corroded metal and leave it for several tens of minutes depending on the severity of the corrosion. In the meantime, the nanoparticle layer penetrates the rust into the metal itself. Then you just need to clean the surface with a cloth or in heavier cases with a brush. You will remove the corrodes and prevent further propagation.

- Erases joints

Just a few drops of nanoparticle solution into the door hinges and for long time you get rid of annoying screeching. The lubricant can be applied to all moving mechanical parts to ensure their long-term lubrication and preservation.

- Enables tightened mechanisms and screws

The solution is characterized by strong gait, so miniature nanoparticles can penetrate into very thin gaps. For example, if you need to allow a screwdriver, apply a NANOPROTECH Auto Moto Anticor spraying dose and let it work. After 10-15 minutes, the nanoparticles penetrate under the head of the bolt and you release it more easily.

- Protects against freezing

NANOPROTECH sprays retain their unique capabilities even in extremely cold temperatures. The solution can be applied, for example, to a car lock, which then remains movable even in conditions well below freezing. We also recommend applying it to the rubber seal around the door to prevent it from freezing. Similarly, you can protect the fuel tank cover and other endangered parts.

Properties:

- It acts as anticorrosive protection
- Resistant to temperatures from -80 ° C to +160 ° C
- It works for up to 1 year
- Consumption: approx. 50 ml per 1 m2
- Contents: 300 ml

Where to use spray?

- Door, trunk and bonnet locks
- Rubber door seals and operating holes
- Suspension and towing devices
- Screws, mothers
- Hinges, hinges, pins

How to use spray?

- Apply spray in well-ventilated areas and preferably with protective gloves.
- Carefully shake before spraying
- Spray a continuous layer (at a distance of 20-30 cm) on the designated surface or use the spray directly on the treated site (screws, etc.)
- Wait 10-15 minutes after application and then wipe the excess solution.